Si/Al composite hollow spheres with a surface hole were prepared with the co-axial microchannel in a one-step method. It is easy to use the technique for size control and continuous operation. At Si/Al ratio between 4 and 5, a hole forms on the surface, due to the fast gelation process and high viscosity of the sol. Scanning electron microscopy, nitrogen adsorption–desorption isotherms, and mercury intrusion method are used to characterize the samples. The hole size is 40–150 μm and the particle size is 450–600 μm. The size can be adjusted by the flow rate of the oil phase.
In this paper,we present a new method for preparing γ-alumina nanoparticles with a bimodal pore size distribution by using an efficiently mixing membrane dispersion microreactor.NH4HCO3and AI2(SO4)3.18H2Owere reacted under vigorous mixing to give an ammonium aluminum carbonate hydroxide (AACH)precursor.γ-Alumina was obtained by calcination of AACH at 550℃ for 6h.The effects of NH4HCO3concentration,pH during aging,and reaction temperature were investigated.The mechanism of bimodal pore formation was clarified.The results showed that large pores (10-100nm) were mainly formed in the reactor and during aging,and small pores (0-10nm)were mainly formed during calcination.When the concentration of NH4HCO3was 1.5mol/L,the aging pH was 9.2,and the reaction temperature was 80℃,γ-alumina with a specific surface area of 504.7m^2/g and pore volume of 1.76mL/g was obtained.The average size of the large pores was about 30nm,and the average size of the small pores was about 4nm.
Lufan YangMingzhao GuoFan ZhangYu JingYujun WangGuangsheng Luo
This paper reviews recent development and achievements in controllable preparation of nanoparticles, micron spherical and non-spherical particles, using microfluidics. A variety of synthesis strategies are presented and compared, including single-phase and multiphase microflows. The main structures of microfluidic devices and the fundamental principles of microflows for particle preparation are summarized and identified. The controllability of particle size, size distribution, crystal structure, morphology, physical and chemical properties, is examined in terms of the special features of microfluidic reactors. An outlook on opinions and predictions concerning the future development of powder technology with microfluidics is specially provided.
Guangsheng Luo Le Du Yujun Wang Yangcheng Lu Jianhong Xu
A subcritical water treatment method was developed for preparing porous-surfaced glass beads with an egg-shell structure in a batch reactor. Based on the ＂corrosion-ion-migration-recondensation＂ strategy, ordinary soda-lime glass beads with a diameter of about 100 um were made first to react with subcritical water to effect controlled quantity of silicate dissolution of glass by adjusting treatment time and temperature. The dissolved silicate was then made to recondense on the glass core to form different porous shell morphologies： pores, flakes and fibers. Among these, glass beads coated with fibers with surface area of 154.5 m2/g, pore volume of 0.27 cm3/g and pore size of 7.1 nm were obtained at 573 K after 2 h of treatment. The prepared porous-surfaced glass beads were then used as adsorbent for heavy metal ions, showing various ion exchange properties. Glass beads covered with fibers displayed fast kinetics and high sorption capacity because of their egg-shell structure and high surface area. More than 90% of copper ions were adsorbed within 100 min from a solution with an initial concentration of 110 mg/L at 313 K. Ion sorption capacities were 149.33, 81.33 and 42.96 mg/g respectively for Ag＋, Cu2＋ and Ni2＋ at 313 K. A green and low-cost method was thus developed to produce egg-shell-structured porous glass with high sorption capacity.
Chun ShenYujun WangJianhong XuYangcheng LuGuangsheng Luo
Indium hydroxide(ln(OH)3)and indium oxide(ln2O3)particles are typically synthesized through chemical precipitation methods.In this study,we used a seed-mediated growth method and microreactor-based synthesis process.We synthesized cubic In(OH)3 particles with a crystal size of 172 nm from an 5%(w/v)indium chloride solution.The In2O3 particles synthesized through the thermal decomposition of In(OH)3 particles featured crystals up to 90 nm in size with an average size of 73 nm,which were much larger than the 20-30 nm In2O3 particles synthesized by a traditional precipitation method.The concentrations of the seed and growth solutions were varied from 1%to 7%(w/v).The crystal size of the particles increased with the concentration of the seed and growth solutions;this tendency was the opposite to that observed for the precipitation method.Through the use of a 5%(w/v)seed solution,the flow rate of the growth solution was varied from 1 to 10mL/min,and the resulting crystal size decreased as the flow rate was increased.To understand the reasons for this trend,the growth rate of the crystals was determined at different flow rates(i.e.,1,5,and 10 mL/min).A growth model consistent with the experimental results was established,which demonstrated that slow addition of the growth solution was beneficial for preparing large indium hydroxide particles.
Jingchuo WangShaoqing BaiYujun WangGuangsheng LuoTao Wang
